Skip to main content

Prototype Green House / Shed DIY Kit Mk 1 with Slanting Flat Roof (Using DES Strips & Grp Sheets)

Prototype Green House / Shed 1
Thsi is exploring a method for making a one-off shed.
If it was repeated in manufacture , it could be used as a pattern.
my intention is to make differnt roof types to fit the cube base like the previous WedgeBlock shelter 


 Make 4 x 2 mtr square frames with corner braces. Then 2 triangular roof side frames

Note: the top & bottom frames have the grp side on the top & bottom to take the extra weight of the roof ( the composite DES sticks are weaker if facing the othe way)  


 Close up

 1. Screw 4 x frames together to form a cube.
2. Move frame onto its' side
3. Screw 2 triangular roof side frames to cube frame


 Screw Grp sheets to the side temporarily and cut to size.

Note: sometime the off cut slanted side is the same angle as the adjoining panel, so it can be reused as the neighbouring panels


 Close up of other side



















Comments

Popular posts from this blog

Paul Ridley, Founder of the Cabinz Project has invented "Shelter Banks" Where People Can Collect Materials to Build Basic Shelters

Press Release:

"Shelter Banks" Similar to Food Banks.Providing Building Materials For Outbuildings, to People Squeezed Into The Smallest Houses in Europe


The Uk Property market has been in crisis for many years. The new concept of Shelter Banks, aims to help ease a part of that crisis.

They are similar to Food Banks in the Uk, but distributing, re-used & re-manufactured building materials that have been donated or bought in bulk at low cost.
The shelters built with these materials, may be storage sheds, greenhouse or insulated garden offices for small businesses.

To facilitate this, building materials are stored in a warehouse and collected by local people, or posted to target low income groups, individuals or small businesses over a wider area.

Some materials will be free, but it depends on the amount of resources, funding & donations available, as to whether materials will have to have a small charge. If so, due to low overheads & donator support, they will much chea…

Treated 6mm Birch Plywood Shingle Off Cut Cladding Shelter Experiment

Treated 6mm Birch Plywood Shingle was screwed to 2m Plastic Door edge strip (DES) horizontal battons. 42mm & 75mm drywall screws were used (no extra glue)

The off cuts were donated from a local fencing co. that also make rabbit hutches, from which these off cuts arose

Off cuts were dipped in decking / fencing preserver, so a few 'tide marks' are present.
This was done to get more preserver deeper into the wood .

We wait to see how it weathers & it will hopefully make our first prototype shelter more attractive (still going strong after 2.3 yrs)

More off cut cladding picture variations to come 

Some off cuts have been donated to Woodcraft to Wellness Chester













Close up







Hurricane Damaged Shelter Recovery Method for British Virgin /Caribbean Islands / Usa with little or no budget

Hurricane Damaged Shelter Recovery Proposal Method for British Virgin /Caribbean Islands / Usa with little or no budget
Hurricanes Harvey and Irma Damage, America Can’t Afford to Rebuild 
Method 
1. Collect wood that is plentiful due to fallen trees / joists / stick frames 
2. Sort or cut wood into 50mm /70 / 140mm thick planks
3. paints planks with preservative 
4. Clad & nail / screw planks inside galvanised drywall lining channel or purlins, salvaged from destroyed buildings 
5.Drill holes in structurally sound brick walls, insert plastic walls plugs , glued in with injection resin or adhesives
6. Screw metal clad  planks to wall, horizontally & vertically , so a 2.4 x1.2m sheet can be screwed to it    
7  Fill insulation voids with plastic bottles filled with polystyrene or bubble wrap (or sand / soil / water if thermal mass / heavier wall weight required) .